Snowmobile maintenance is mostly a set of repeating jobs: greasing the suspension, checking hardware and track, keeping the belt and clutches in good shape, and servicing fluids on schedule. This page covers where the grease points are, how to grease them, and a season checklist. Your owner’s manual overrides anything here. Zerk locations, intervals and specs vary by model and year.
Where the grease points are
Most suspension grease points are at the pivots:
- Rear suspension pivot shafts, on the front and rear arms
- Rear shock linkages
- Front A-arm pivots
- Spindles
- Steering post bushings
Zerk count and location vary by chassis. Many newer sleds have sealed or greaseless pivots, so the fitting you’re looking for may not exist. Check the lubrication diagram in your manual before you start. Many Polaris rear suspensions, such as Rush, AXYS and Matryx, have several zerks on the arms. Front ends vary by year.
How to grease a zerk
- Park the sled on a level surface with the engine off and the key and tether removed.
- Raise the rear so the suspension is unloaded. Support the sled on a stand, not by hand or on a jack alone.
- Wipe the zerk clean so grit doesn’t get pushed into the joint.
- Attach the grease gun squarely to the zerk.
- Pump until fresh grease comes out of the joint. That pushes out old grease and any water.
- Wipe off the excess.
If a zerk won’t take grease, clean it or replace it. Don’t keep forcing the gun, because you can damage the fitting or the seal behind it.
For the grease itself, see what grease to use on a snowmobile.
What not to grease
- Clutches. Sheaves, buttons and rollers usually run dry, unless the manufacturer says otherwise.
- Sealed bearings. They can’t be greased. Only fittings with zerks take grease.
Season checklist
Work through this list at the start of the season and before any long trip. The items vary by model, so check each one against your manual.
Suspension and hardware
- Check the rear idler wheel bolts and the adjusting bolt locknuts for tightness.
- Check the front torque arm limiter strap.
- Check slide rails (Hyfax) for wear. Replace them at the wear limit in the manual.
- Check the ski runners and carbides. Replace them when worn or rounded, per the manual.
- Lubricate all suspension components.
Track and drive belt
- Check track tension and alignment often early in the season. Specs vary by model.
- Inspect the drive belt for glazing, cracks and missing cogs. Check its deflection and carry a spare. For belt problems, see snowmobile drive belt problems. For tension, see how tight the belt should be.
Chaincase
- Check the chaincase oil level each season, and change the oil at least once a year. See how to change snowmobile gearcase oil.
Brakes and coolant
- Many current sleds use DOT 4 brake fluid. Replace it on the interval in your manual, since the interval varies.
- Check the coolant level when the engine is cold. Use the premix or ratio the manufacturer specifies.
Engine and intake
- Four-stroke engines need oil and filter changes on schedule and before storage. See how often to change snowmobile oil.
- Two-strokes don’t need engine oil changes. Keep the injection tank filled.
- On carbureted sleds, keep the intake and carbs in good shape. See how to clean a snowmobile air filter and how to clean a snowmobile carburetor.
Storage prep
Off-season storage is where a lot of avoidable damage starts. Common steps include:
- Stabilize the fuel and run the engine briefly to circulate it. See old gas in a snowmobile.
- Fog the engine, if your manufacturer recommends it. See how to fog a snowmobile engine.
- Remove road salt and grime from the surfaces before you apply any wax or rust inhibitor.
- Grease the fittings, including the ones that are easy to miss.
- Loosen the track and raise it off the floor.
- Store the sled in a dry garage or shed, out of direct sunlight, under a fabric cover. A plastic tarp can trap condensation.
- Block rodents from the intake and exhaust.
Safety
- Turn the engine off and remove the key and tether before you work near the clutches or the track.
- Support a raised sled on a stand. Don’t rely on a jack alone or on your hands.
- Keep hands and clothing away from the belt and clutches while the engine is running.