A snowmobile’s track and rear suspension work as one system. The track provides traction and flotation. The rear suspension, called the skid, holds the track in shape, absorbs bumps, and controls how much weight sits on the skis. Once you see how the two fit together, the choices are easier: which track to buy, how to set it up, and when to replace it.
There is no single best snowmobile track. The right one depends on your sled’s specification, the terrain you ride, and how hard you ride. The sections below cover each part and link to a detailed guide for each.
How the track and rear suspension work together
The track is a continuous rubber belt reinforced with fabric and transverse rods. Outer lugs grip the snow. Inner drive lugs engage the drive sprockets. Metal guide clips on the inside of the track ride on slide rails covered with hyfax, a plastic wear strip that keeps the track centered.
The skid is the set of parts that carries the track: the slide rails, front and rear arms, shocks, springs, and idler wheels. It bolts to the tunnel, usually with about four main bolts, though this varies by model.
The two depend on each other. A track that is too tight adds drag and wears hyfax. A skid with the wrong preload changes how much weight the skis carry. A worn drive sprocket can damage a new track. Read the sections together rather than in isolation.
Track basics: width, length, pitch, and lug height
Track size is written as width × length × lug height, followed by the pitch. A track listed as 15 × 137 × 1.25 in., 2.52 pitch, is 15 in. wide, 137 in. long, has 1.25 in. lugs, and uses 2.52 in. pitch.
Most sleds use 15 in. wide tracks. Some models use 16 in. Utility sleds may use 20 or 24 in. Pitch matters as much as length. Most trail sleds run 2.52 in. pitch, and many mountain sleds use 2.86 or 3.0 in. The drive sprockets must match the pitch.
Lug height changes with the riding. Trail tracks have shorter lugs, and deep-snow and mountain tracks have taller ones. Taller lugs are limited by tunnel and heat exchanger clearance, so a taller track is not always a simple bolt-on change.
What size snowmobile track do you need?
Start with the size your sled was built for. The owner’s manual and a fitment chart from the track maker list the length, width, lug height, and pitch for each make, model, and year. The track length has to match the skid. The track adjusters only take up stretch over a small range, so tensioning cannot fix a track that is the wrong length.
Track length also depends on terrain. Trail sleds commonly use lengths from about 121 to 137 in., while crossover, deep-snow, and mountain sleds use longer tracks. For how to measure a track and the trade-offs of each length, see snowmobile track length: how to pick the right size.
Choosing a track for your riding
Once the size is right, the choice comes down to how the track handles your riding. Three decisions matter most.
- Ply count. A 1-ply track is lighter and accelerates quicker. A 2-ply track is stiffer and tougher. See 1-ply vs 2-ply snowmobile tracks.
- Studs. Studs add bite on hardpack and ice, but they need a track and setup that allow them. See studded snowmobile tracks and ice scratchers.
- Track type. Trail, on-off trail, mountain, utility, and racing tracks are built for different snow. Shorter setups handle groomed trails well, while longer ones float better in deep powder.
Parts of the rear suspension
A skid usually has two aluminum slide rails with hyfax, front and rear arms, front and rear track shocks, rear springs, idler wheels, a rear idler axle with track adjusters, a limiter strap, and cross shafts. Some skids couple the front and rear arms, which limits pitching and bottoming. Design details vary by brand.
For a plain walkthrough of the skid, read what is a skid on a snowmobile?
Springs, shocks, and sag
Rear springs are usually torsion springs with preload cams or blocks. Some designs, such as the Ski-Doo rMotion, use a coil-over rear shock instead. Most shocks are oil-damped, and many use nitrogen pressure to keep the damping steady when hot.
Spring preload changes ride height and sag. It does not change the spring rate. After the rear is set, ski pressure is tuned at the front with the front track spring and the limiter strap.
To set the rear, measure free sag and rider sag, then adjust preload. See how to set rear suspension sag on a snowmobile. For the difference between oil and gas shocks, see snowmobile shock absorbers: oil vs gas explained.
Keeping the track and skid in tune
Track tension and alignment are set with the rear raised, in that order: tension first, then alignment. A track that is too tight adds drag, lowers top speed, and wears hyfax and bearings. A track that is too loose can ratchet and can strike the tunnel or heat exchanger. Check your manual for the spec. New tracks stretch, so recheck tension after roughly the first 50 miles. See how to adjust snowmobile track tension.
Hyfax wears fastest on ice, hardpack, and roads, and it needs snow to cool and lubricate it. Replace both sides as a pair when the hyfax reaches its wear limit. See snowmobile hyfax: when and how to replace slide rails.
When a track needs replacing
Replace a track when its structure is damaged, not just when it looks worn. Exposed rods or cords, torn belting, deep cracking, many missing lugs, worn drive lugs that cause ratcheting, and stretch past the adjuster range are the main signs. Cosmetic lug wear on its own is less clear-cut. See when to replace a snowmobile track: wear signs and lifespan.
Removal and installation at a glance
Removing a track means removing the skid and then the driveshaft, because the track is a closed loop. Installing it reverses that: the track goes into the tunnel, the driveshaft is fed through the loop, the drivers are timed, and the skid is bolted back in. Set tension and alignment last. For each job, see how to remove a snowmobile skid and track and how to install a snowmobile track, step by step.
Safety basics
Several parts of this work can injure you. Loaded springs and compressed shocks store energy, so keep your hands clear and use the proper tools. Never work under a sled held only by a jack. Use a stand or hoist. Never spin a lifted track near people, and never stand behind or beside one. A damaged track can come apart at speed, so do not ride on one with broken or exposed rods.
Where to read next
- Track sizing: snowmobile track length, are snowmobile tracks universal?
- Choosing a track: 1-ply vs 2-ply snowmobile tracks, studded tracks and ice scratchers
- Suspension: what is a skid on a snowmobile?, how do snowmobiles work?, oil vs gas shock absorbers, rear suspension sag
- Maintenance and replacement: track tension, hyfax replacement, when to replace a track, track removal, track installation