Tracks and Suspension

How to Set Rear Suspension Sag on a Snowmobile

How to set rear suspension sag on a snowmobile: measure free sag and rider sag, adjust spring preload, and tune ski pressure with a fixed reference point.

On this page
  1. What sag means
  2. What you need
  3. Step 1: Measure full extension (A)
  4. Step 2: Measure free sag (B)
  5. Step 3: Measure rider sag (C)
  6. Choosing a target
  7. Adjust preload
  8. What preload does and does not change
  9. Tune ski pressure after sag
  10. Common myths
  11. Safety

Sag is how far the rear suspension compresses under the sled’s own weight and under the rider. Setting it is the starting point for the rest of the suspension, because it changes ride height and how much weight the skis carry. This guide covers how to measure free sag and rider sag, how to choose a target, and how to adjust preload.

What sag means

  • Free sag is how far the rear compresses under the sled’s own weight, with no rider aboard.
  • Rider sag is how far it compresses with the rider in full gear.

Both are measured from the same fixed point, so you can compare readings from one setup to the next.

What you need

  • A helper
  • A fixed reference point on the tunnel or the rear bumper
  • A tape measure or ruler
  • The gear you normally ride with, including fuel, cargo, and passenger load if you carry them

Set up with your usual load. A sag reading means little if the load changes between measurements.

Step 1: Measure full extension (A)

Lift the rear until the suspension is fully extended. Measure from the reference point straight down to the ground. Call this measurement A. Take two or three readings and average them, because friction between the slide rails and the track makes single readings less consistent.

If the rear stays at full extension when you set the sled down unloaded, the suspension is “topping out.” That means preload is likely too stiff.

Step 2: Measure free sag (B)

Set the sled down unloaded. Cycle the suspension a few times, let it settle, and measure again from the same reference point. Call this measurement B. Free sag is A minus B.

Step 3: Measure rider sag (C)

With the rider in full gear, in the normal riding position, let the suspension settle and measure again. Call this measurement C. Rider sag is A minus C. Take two or three readings and average them, as before.

Choosing a target

Start with the target in your owner’s manual or the shock maker’s guidance. If you do not have a number, a commonly used starting point is a rider sag of about one-third of the rear travel. Published targets differ between sources, and they can use different reference points. Treat any figure as a starting point, then ride the sled and adjust from there.

Adjust preload

Preload is the spring’s compression before any weight is applied. Adjust it with:

  • Torsion spring cams or blocks, on sleds with torsion springs. Set both springs to the same position.
  • A threaded collar, on coil-over rear shocks such as the Ski-Doo rMotion.

Make small changes, and remeasure after each one.

What preload does and does not change

  • More preload means less sag, a higher rear, and more ski pressure.
  • Less preload means more sag, a softer initial feel, and less ski pressure.
  • Preload changes ride height, not spring rate. If you need extreme preload to reach your target, a different spring may be the right fix.

Tune ski pressure after sag

Once rear sag is set, tune ski pressure with the front track spring and the limiter strap. A stiffer front track spring means less ski pressure, and a softer one means more. A shorter limiter strap means less weight transfer and more ski pressure, while a longer strap allows more weight transfer. Make one change at a time, and ride between changes.

Common myths

  • “More preload makes the spring stiffer.” It changes ride height. The spring rate stays the same.
  • “You can set sag with the sled alone.” You need a rider aboard in full gear.
  • “One setting suits every rider.” Weight, gear, and riding style all change the answer.
  • “Sag only affects comfort.” It also changes handling and ski pressure.

Safety

Turn torsion spring cams with the proper tool. Loaded springs can snap back, so keep your hands clear of the spring and its cam.

For the parts you are adjusting, read what is a skid on a snowmobile?. For shock damping and the difference between oil and gas shocks, see snowmobile shock absorbers: oil vs gas explained. If a preload change affects your track, how to adjust snowmobile track tension covers the recheck. For the wider picture, see snowmobile tracks and rear suspension explained.

The complete guide to tracks and suspension

Snowmobile Tracks and Rear Suspension Explained
Read the guide

Keep exploring

Guides from other topics

All topics →