Ways to haul a snowmobile
There are four common ways to haul a snowmobile:
- Pickup truck bed. You load the sled straight into the bed, usually with a ramp. It is the simplest option if you already own a truck, but the sled is exposed to weather and road salt.
- Sled deck in a pickup. A platform that fits in the bed holds the sled higher and can carry up to two sleds, depending on the deck. It loads quickly, but it costs more and takes up the bed.
- Open trailer. Lighter, usually cheaper, and easy to load from the front or side. The sled is exposed to salt, slush, and debris, so it needs a cover for road trips.
- Enclosed trailer. Protects the sled and gives you lockable storage. It is heavier, needs a tow vehicle with enough capacity, and needs venting for fuel fumes.
The right choice depends on how far you travel, how many sleds you haul, and what your tow vehicle can pull. The sections below cover each method, then the hitch, loading, securing, and pre-trip steps that apply to all of them. If you are still deciding on a trailer, the open vs enclosed trailer guide compares them in more detail.
Pickup truck beds and sled decks
Yes, you can haul a snowmobile in a truck bed. Drive the sled up a ramp, secure it, and drive to the trail. The loading guide covers the steps in order.
Short beds need some care. On a bed about 5.5 to 6.5 ft long, a sled can overhang the lowered tailgate. Many states require a red flag or light on a load that overhangs the rear by a set distance, often around 4 ft. The exact rule varies, so check your state’s rules before you drive. Keep the sled as far forward in the bed as the ramp and tie-downs allow.
Truck ramps should be long enough to keep the angle shallow, and rated well above the sled’s weight. Sled weights commonly fall between about 450 and 750 lb, so check the ramp’s weight rating against your sled, not just its length or width. Secure the ramp to the tailgate so it cannot kick out.
If you have no ramp at all, the guide to loading without a ramp explains the options, including backing into a snowbank.
Open and enclosed trailers
Trailers are the usual choice for longer trips or for more than one sled.
Open trailers come as tilt-bed, drive-on, or low-profile decks. A tilt bed tilts down to the ground so the trailer acts as its own ramp. Do not add a ramp to a tilt bed, because the trailer is not built for that and the tilt system can be damaged. Open trailers need a cover for highway trips. Remove the windshield or use a trailerable cover, since a regular storage cover can flap, tear, and chafe paint at speed.
Enclosed trailers protect the sled and give you storage. Inline models have a drive-on, drive-off ramp door at the rear, while V-nose models have a tapered front with more room for skis. Enclosed trailers are heavier, catch more wind, and use more fuel. Fuel vapors can build up inside, so vent the trailer and never smoke or run a heater with fuel odor present.
Matching the hitch, tow rating, and tongue weight
Your hitch, ball, and tow vehicle rating all need to match the loaded trailer. Sleds are only part of the weight. Do not assume any receiver will do.
- Tongue weight: aim for roughly 10 to 15% of the loaded trailer weight. Load sleds forward of the trailer axle to help.
- Brakes: many states require brakes on trailers above a set weight, often somewhere between 1,500 and 3,000 lb. Check your state’s rule.
- Safety chains: cross them under the coupler.
- Before each trip: check lights, tire pressure, and wheel bearings. Road salt corrodes trailer parts, so rinse the trailer after winter trips.
Loading and securing
Load in a flat, open area, with the tow vehicle in park and the parking brake set. Use steady, moderate throttle on the ramp, and do not stop halfway. Once the sled is on the deck, shut it down, remove the key, and secure the skis and track before you move. The loading guide walks through each step, and the tie-down guide explains how to strap the sled.
Use at least two straps per sled: one at the front and one at the rear. Rope and bungee cords are not suitable as primary tie-downs. Re-check straps after the first 10 to 25 miles and at every fuel stop, because they loosen as the load settles.
Fuel and pre-trip checks
For normal road trips you usually do not need to drain the tank. Do not fill it to the brim, since fuel expands as it warms and can vent. If your sled has a fuel shutoff, close it for transport. Tighten the gas cap. The fuel guide covers when draining is required, such as for some freight or air shipments.
When a professional hauler makes sense
If you are moving sleds a long way, relocating, or do not have a suitable tow vehicle, a professional transport service may be worth the cost. Some companies offer enclosed multi-sled transport and insurance. Ask how they load and secure sleds and what their insurance covers before you book. Your own snowmobile insurance may also cover damage while the sled is being trailered.
Pulling a disabled sled is a different job
Towing a broken-down sled behind another sled on snow is not the same as hauling on a trailer. It needs different gear and different technique. See the towing guide for that job.
Choosing the right sled and gear
Some sleds handle towing far better than others. Utility sleds with wide, long tracks and low gearing are usually the best choice for hauling and towing, while trail and mountain sleds tend to struggle. The towing sled guide explains why.
Moving a sled around the garage is also easier with the right gear. Dollies and carts protect the track and the floor, and keep the sled off a cold, damp floor.
Safety basics
- Never ride or stand in a trailer or truck bed while the vehicle is moving.
- Chock the tow vehicle and set the parking brake before loading.
- Snow and ice cut traction on ramps and decks. Clear them before you load.
- Never run a sled engine inside a closed trailer. Exhaust can cause carbon monoxide poisoning, so keep doors open.