Tracks and Suspension

Snowmobile Hyfax: When and How to Replace Slide Rails

Snowmobile hyfax: how to spot wear, measure it, and replace the slide rail wear strips. Arctic Cat slides are model-specific and do not interchange.

On this page
  1. What hyfax does
  2. Wear signs to check
  3. When to replace
  4. Arctic Cat slides and fit
  5. How to replace hyfax
  6. Upgrades
  7. Common myths
  8. Safety

Hyfax is the plastic wear strip under each slide rail, and the track’s guide clips ride on it. When hyfax wears down, metal can end up rubbing metal, which damages the clips and the rails. Replace worn hyfax in pairs, using the maker’s wear limit. Arctic Cat slides are model-specific, so check the part number before you buy.

What hyfax does

Hyfax is UHMW polyethylene, a tough, slick plastic, fitted to the bottom of each aluminum slide rail. The track’s guide clips slide along it, which keeps the track centered and lets it run smoothly. “Hyfax” and “Hi-Fax” began as trade names, but people now use them for these strips in general.

Hyfax needs snow to stay cool and lubricated. It wears fastest on ice, hardpack, and roads. An overly tight track, misalignment, and riding without ice scratchers also speed up wear.

Wear signs to check

Look for:

  • Scalloped or melted edges
  • Grooves worn into the surface
  • Missing chunks
  • Black deposits on the guide clips

Check the hyfax with the rear raised, so you can see the full length of each slide.

When to replace

Measure the thickness at several points along each slide. Replace the hyfax at the OEM wear mark or minimum. On some sleds, the rule is to replace it before the rail or the bolt heads touch the clips. The exact limit varies by model, so use the manual. Replace both sides as a pair, even if only one looks worn.

Arctic Cat slides and fit

Arctic Cat skids use model-specific slides, such as the Slide-Action and the Alpha One single-beam. Slides do not interchange across brands or models. Check the part number against your sled’s model and year before you order. A slide that looks similar may not fit the rail’s shape or the screw locations.

How to replace hyfax

Replacing hyfax is easiest with the skid off the sled, although some models allow the job in place. The general steps are below. Follow your manual for the exact order.

  1. Raise the rear and back the track adjusters off fully.
  2. Remove the retaining screw near the front of the slide. Its location varies by model.
  3. Drive the old slide off, usually toward the rear, using a wood block and a mallet.
  4. Clean the rail, file off any burrs, and check the rail for bends.
  5. Warm the new slide in hot water, or use soapy water, to help it go on.
  6. Fit new screws and seat the new slide.
  7. Reinstall the skid if you removed it, then set track tension and alignment.

Keep your fingers clear when you drive the slide, and support the sled on a stand for the whole job.

Upgrades

Some riders upgrade to low-friction slides, such as graphite, or add rail idler-wheel kits or ice scratchers. Check that any upgrade fits your model before ordering. For how scratchers work and when to raise or lower them, see studded snowmobile tracks and ice scratchers.

Common myths

  • “Worn hyfax can be ignored.” Metal on metal can ruin the clips and rails.
  • “Any hyfax fits any rail.” Slides are model-specific.
  • “Low-friction slides do not need snow.” They still need snow to keep the track and slides cool.
  • “Wear comes from mileage alone.” Low-snow heat is usually the main cause.

Safety

Support the sled on a stand. Keep your fingers clear when you drive the slides.

For the skid these slides belong to, read what is a skid on a snowmobile?. After replacing the slides, set tension and alignment with how to adjust snowmobile track tension. For the wider picture, see snowmobile tracks and rear suspension explained.

The complete guide to tracks and suspension

Snowmobile Tracks and Rear Suspension Explained
Read the guide

Keep exploring

Guides from other topics

All topics →