Tracks and Suspension

How to Install a Snowmobile Track Step by Step

How to install a snowmobile track step by step: check fit, feed the driveshaft through the loop, time the drivers, refit the skid, and set tension.

On this page
  1. Before you start
  2. Step 1: Set the track in the tunnel
  3. Step 2: Feed the driveshaft through the loop
  4. Step 3: Time the drivers
  5. Step 4: Reinstall the drivetrain parts
  6. Step 5: Fit the skid and bolt it on
  7. Step 6: Set tension, then alignment
  8. Check clearance with taller lugs
  9. Break-in and recheck
  10. Common myths
  11. Safety

Installing a track is mostly the reverse of removing one. The skid and driveshaft come out, the new track goes into the tunnel, the driveshaft is fed back through the loop, and the parts go back together. Set tension and alignment last. Follow the order below, and check your manual for torque values and any model-specific steps.

Before you start

  • Confirm the fit. Check the new track’s width, length, lug height, and pitch against a fitment chart for your sled. For how to read those specs, see are snowmobile tracks universal?
  • Install any studs first. Put studs in before the track goes on the sled. For the rules, see studded snowmobile tracks and ice scratchers.
  • Check the drive sprockets. Replace worn ones now, because they can damage a new track.
  • Get the tools and the manual ready. If the old track is still on, the removal guide covers the steps that come first.

Step 1: Set the track in the tunnel

With the skid and driveshaft out, set the track into the tunnel. Make sure it turns in the direction of its rotation arrow. Check the arrow before you go further.

Step 2: Feed the driveshaft through the loop

Feed the driveshaft through the track loop and seat the drivers into the track’s drive lugs. Each driver should sit fully in its lug before you move on.

Step 3: Time the drivers

Time the drivers so both sprockets sit in the same position relative to the track. Timing matters for a smooth drive. Use the reference marks in your manual for your model.

Step 4: Reinstall the drivetrain parts

Reinstall the bearing housings, the chaincase sprocket, the chain, and the tensioner. Set the chain tension according to the manual. Refill the chaincase or gearcase to the correct level with the oil the manual specifies.

Step 5: Fit the skid and bolt it on

Fit the skid into the track loop, line up the arm mounts with the tunnel, and install the bolts. Use threadlocker where the manual calls for it, and torque each bolt to spec.

Step 6: Set tension, then alignment

Set track tension to your manual’s spec, then check alignment. Run the track slowly on the stand, and check that it tracks straight. The full procedure is in how to adjust snowmobile track tension.

Check clearance with taller lugs

If the new track has taller lugs, turn it by hand with the suspension compressed. Check that it clears the tunnel and the heat exchangers. A track that rubs can cut into a cooler and leak coolant, so do not skip this check.

Break-in and recheck

New tracks stretch. Ride moderately at first, then recheck tension after roughly the first 50 miles, and recheck alignment at the same time.

Common myths

  • “Track direction does not matter.” It does. Follow the rotation arrow.
  • “Drivers do not need timing.” They do.
  • “Tension is set once and forgotten.” New tracks stretch, so recheck.
  • “Old drivers are fine with a new track.” Worn drivers can damage a new track.

Safety

Support the sled on stands, not a jack alone. Never spin a lifted track at speed, or with anyone behind it.

Once the new track is in, the skid and suspension are the next things to check. Read what is a skid on a snowmobile? for the parts, and how to set rear suspension sag on a snowmobile for the rear setup. For the wider picture, see snowmobile tracks and rear suspension explained.

The complete guide to tracks and suspension

Snowmobile Tracks and Rear Suspension Explained
Read the guide

Keep exploring

Guides from other topics

All topics →