Sled Maintenance

How to Change Snowmobile Gearcase Oil

How to change snowmobile gearcase or chaincase oil: checking the level, draining the old oil, inspecting it, refilling, and checking chain tension.

On this page
  1. When to change it
  2. Which oil to use
  3. What you need
  4. Step by step
  5. If there’s no drain plug
  6. What the drained oil tells you
  7. Check the chain tension
  8. Torque and overfilling
  9. Common mistakes
  10. Safety

The gearcase, or chaincase, is the housing around the drive chain and sprockets that set the sled’s gearing. It needs fresh oil once a year. Most sleds have a chain-and-sprocket chaincase. Some utility models have a gearbox. The steps are similar, but check the manual for your model.

When to change it

  • Check the oil level every season.
  • Change the oil at least once a year, or at the interval in your manual.
  • The first change is often recommended after break-in. The manual has the timing.

Which oil to use

  • Polaris: Polaris Synthetic Chaincase Lubricant
  • Ski-Doo: XPS Synthetic Chaincase Oil
  • Arctic Cat: Arctic Cat Synthetic Chaincase Oil
  • Utility gearboxes: may call for a gear oil. Use the grade in your manual.

Chaincase oil isn’t interchangeable with other gear oils, because viscosity and cold flow matter. Use the oil your manual specifies.

What you need

  • The correct oil, in the amount your manual gives
  • A drain pan
  • A suction gun or pump, if your chaincase has no drain plug
  • A new O-ring or sealing washer for the drain plug
  • A torque wrench for the drain plug and the cover bolts

Step by step

  1. Park the sled on level ground. Turn the engine off, and remove the key and tether.
  2. Let the oil warm slightly so it drains better, but let it cool enough to handle safely.
  3. Remove the drain plug if your chaincase has one, and catch the oil in the pan.
  4. If there’s no drain plug, siphon the oil out with a suction gun, or remove the cover. See the next section.
  5. Inspect the drained oil. See the section on what the drained oil tells you, below.
  6. Clean the magnetic drain plug, and fit a new O-ring or sealing washer.
  7. If the cover is off, check the chain tension, adjust it to spec and refit the cover.
  8. Refill to the level your manual gives. Use the dipstick mark, the check plug or the specified volume.
  9. Torque the drain plug and cover bolts to spec.

If there’s no drain plug

Many chaincases have no drain plug. Siphon the oil with a suction gun, or remove the cover and drain it. Removing the cover also gives you access to the chain and sprockets for the tension check.

What the drained oil tells you

  • Milky oil means water has got in. Find the source before you refill.
  • Glitter or chunks in the oil point to wear in the chain, sprockets or bearings.

Clean oil is a good sign. If you see either problem, have the sled inspected before you ride.

Check the chain tension

With the cover off, check the chain tension and adjust it to the spec for your model. Tensioner methods and free-play specs vary. Automatic chain tensioners still wear and need inspection.

Torque and overfilling

Torque the drain plug and cover bolts to the spec in your manual. Chaincase housings are often aluminum, and they can strip easily.

Don’t overfill the case. Extra oil doesn’t add protection, and it can push oil past the seals and vents.

Common mistakes

  • Using the wrong oil. Chaincase oil isn’t interchangeable with other gear oils.
  • Assuming no leaks means no service. Oil breaks down with use and collects wear metal, even if it doesn’t leak.
  • Overfilling. It can push oil out past the seals and vents.

Safety

  • Turn the engine off and remove the key and tether. The track and driveshaft can move when the chaincase is serviced.
  • Support the sled securely if you raise the rear.

The complete guide to sled maintenance

Snowmobile Maintenance: Grease Points and Service Checklist
Read the guide

Keep exploring

Guides from other topics

All topics →