Engine Troubleshooting

Snowmobile Won't Start: A Step-by-Step Troubleshooting Guide

Snowmobile won't start? Work through the kill switch, fuel, spark, battery and flooding checks in order, and learn what backfiring tells you about the cause.

On this page
  1. Start with the basics
  2. The most common causes, in order
  3. Check for spark
  4. Check the battery on electric-start sleds
  5. Battery-less EFI sleds
  6. Check compression
  7. What backfiring tells you
  8. Check the fuel system
  9. Mistakes to avoid
  10. Safety

Most snowmobile no-starts come down to a short list of causes, and the simplest ones are the most common. Work through them in order before you start pulling parts. This guide covers the checks that find most problems, then what backfiring tells you.

Start with the basics

Before you check anything technical, confirm the sled is ready to run:

  • Key on, and the emergency stop switch in RUN.
  • The tether clip attached to the switch.
  • Fuel in the tank, and fuel that is fresh enough to burn.

A kill switch or tether that isn’t in the run position is one of the most common reasons a sled won’t start, and it takes seconds to check.

Fuel is the second check. Ethanol-blended gasoline can go stale in about 30 days without a stabilizer, and many manufacturers recommend no more than E10. If the sled sat through a mild spell or over the summer, drain or replace the old fuel before you go further.

The most common causes, in order

When the basics are fine, the causes usually fall into five groups, roughly in this order:

  1. Kill switch or tether
  2. Stale fuel
  3. Fouled or wet spark plugs
  4. A weak battery
  5. Flooding

Wet, fuel-soaked plugs point to a flooded engine. Dry plugs after cranking point to no fuel reaching the cylinder. Plugs that look fine but give no spark point to the ignition, which is covered below.

Check for spark

Remove a plug, attach it to its plug wire, ground the plug’s base to the cylinder head, and crank the engine. A healthy spark is strong and blue-white. A weak spark is thin and orange.

Hold the plug with insulated pliers, and test away from spilled fuel and open fuel vapor. If you don’t get a strong spark, see what causes a snowmobile to lose spark.

Plug gap is often about 0.028 to 0.035 inch on 2-stroke sleds, but the spec varies by model, so check the manual before you adjust it.

Check the battery on electric-start sleds

A battery at rest should read about 12.4 volts or more. Around 12.6 to 12.8 volts means fully charged. If the starter clicks but doesn’t crank, the usual causes are a weak battery, a corroded terminal, or a faulty starter solenoid. Clean the terminals first, then test the battery under load. If the battery isn’t charging at all, see snowmobile battery not charging.

Battery-less EFI sleds

Many battery-less EFI sleds, including a number of Arctic Cat manual-start models, power the engine control unit and fuel pump from the stator. On these sleds, a short or weak pull may not generate enough output to start the engine. Use a brisk pull through the full length of the cord. Pumping the throttle doesn’t help. For cord technique, see snowmobile hard to pull start.

Check compression

If the engine turns over but never fires, check compression with the plugs out. Healthy 2-stroke compression is often around 120 to 150 psi, and cylinders should read within about 10 percent of each other. The spec varies by model, so use the service manual’s figures.

What backfiring tells you

Where the backfire comes out matters.

  • Backfire through the intake or carburetor usually means a lean mixture or incorrect ignition timing.
  • Backfire through the exhaust usually means unburned fuel is igniting in the pipe. Common causes are a misfire, a rich condition, or one dead cylinder. Check ignition coil failure and a failing fuel pump as possible causes.
  • A sheared flywheel key shifts the timing and can cause backfiring with no start.
  • On twin-cylinder sleds, swapped plug wires cause backfiring and hard starting.

Check the fuel system

Look for a pinched tank vent line, a cracked fuel line, or a clogged in-line filter. On carbureted sleds, a cracked pulse line can also stop fuel delivery. If the sled starts and then dies, see snowmobile runs then dies.

Mistakes to avoid

  • Starting fluid is not a safe fix for a 2-stroke. It strips lubrication. Use it only as a last resort, and sparingly.
  • A new spark plug doesn’t fix every no-start. Replacing plugs without testing for spark wastes time.
  • Backfire doesn’t always mean bad timing. Check fuel and the misfiring cylinder first.
  • More choke often floods a cold engine. Use choke only as the carburetor needs it. Starting a cold snowmobile covers the right steps.
  • Pumping the throttle doesn’t help EFI sleds.

Safety

  • Don’t run the engine in an enclosed garage. Exhaust contains carbon monoxide.
  • Don’t spark-test near spilled fuel or open fuel vapor.
  • Take the tether off while you work near the track or clutches.

If the checks don’t find the problem, or you see damage, take the sled to a qualified shop.

Keep exploring

Guides from other topics

All topics →