Tracks and Suspension

What is a skid on a snowmobile?

What is a skid on a snowmobile? It is the rear suspension assembly under the tunnel that guides the track, holding its shape and absorbing bumps.

On this page
  1. What the skid does
  2. Parts of a skid
  3. How it mounts to the sled
  4. Springs and shocks
  5. Coupled vs uncoupled skids
  6. Skid examples
  7. What you can adjust
  8. Routine skid care
  9. Common myths
  10. Safety

A skid is the rear suspension assembly on a snowmobile. It sits under the tunnel, guides the track, and holds the track in shape while it absorbs bumps. People also call it the rear suspension, the slide-rail suspension, or just the rails. It is a self-contained unit that bolts to the tunnel, usually with about four main bolts, though the count varies by model.

What the skid does

  • Holds the track’s shape and tension
  • Absorbs bumps through its springs and shocks
  • Controls weight transfer, which decides how much weight the skis carry and how the track bites

Parts of a skid

  • Two aluminum slide rails, with hyfax strips on the bottom that the track’s guide clips slide on
  • Front and rear arms, which connect the rails to the tunnel
  • Front and rear track shocks
  • Rear springs, usually torsion springs
  • Idler wheels, which carry the track and spread its footprint along the rails
  • A rear idler axle with track adjusters
  • A limiter strap, which limits how far the front arm can extend
  • Cross shafts, which tie the assembly together

How it mounts to the sled

The skid bolts to the tunnel with about four main bolts, depending on the model. The skid’s length matches the track’s length, so a 137 in. skid runs a 137 in. track. Because the skid is built for one length, choose the track length first. For how to size a track, see snowmobile track length: how to pick the right size.

Springs and shocks

Rear springs are usually torsion springs, with preload cams or blocks that set ride height and sag. Some skids use a coil-over rear shock instead. The Ski-Doo rMotion is one example. Rear travel on modern trail and crossover skids is roughly 13 to 16 in., though it varies by model.

For how the shocks work and why they contain nitrogen, see snowmobile shock absorbers: oil vs gas explained.

Coupled vs uncoupled skids

A coupled skid links the front and rear arms, so they move together to some degree. That helps keep the skis planted and improves traction under hard acceleration, and it limits pitching and bottoming. An uncoupled skid lets the arms move independently. Uncoupled designs are generally described as better for floating in deep mountain powder, though they can make the sled lift or push in trail corners. The details of coupling vary by brand, so check your sled’s manual.

Skid examples

Skid designs differ by riding style. Examples include the Ski-Doo rMotion and rMotion X for trail riding, the Ski-Doo tMotion for mountain riding, the Polaris PRO-XC, and the Arctic Cat Slide-Action and Alpha One single-beam. These are examples of design names, not a complete list. Check your sled’s manual for the exact setup.

What you can adjust

  • Rear spring preload, which sets ride height and sag
  • Front track spring preload, which affects ski pressure
  • Limiter strap length, which affects weight transfer and ski pressure
  • Shock clickers, which adjust damping

Set the rear sag first, then tune ski pressure with the front spring and the limiter strap. For the rear, see how to set rear suspension sag on a snowmobile.

Routine skid care

Grease the pivot fittings, check the idler wheel bearings, and measure the hyfax wear on each slide rail. Track tension and alignment also affect how the skid wears, so set them correctly. For hyfax wear and replacement, see snowmobile hyfax: when and how to replace slide rails.

Common myths

  • “The skid is the skis.” The skis steer. The skid is the rear suspension.
  • “A skid is a flat plate that slides on the snow.” It is a suspension assembly with arms, springs, and shocks.
  • “Skids interchange freely between brands or track lengths.” They do not. The length must match the track, and slides are model-specific.

Safety

Springs and shocks store energy. Support the skid and keep your hands clear when you unbolt it. For the full removal steps, see how to remove a snowmobile skid and track. For the wider picture, see snowmobile tracks and rear suspension explained.

The complete guide to tracks and suspension

Snowmobile Tracks and Rear Suspension Explained
Read the guide

Keep exploring

Guides from other topics

All topics →