Tracks and Suspension

Snowmobile Shock Absorbers: Oil vs Gas Explained

Snowmobile shock absorbers, oil vs gas explained: why gas shocks still contain oil, how nitrogen works, emulsion vs IFP, and what needs service.

On this page
  1. Why shocks have nitrogen
  2. Emulsion and IFP shocks
  3. Remote reservoirs
  4. Air shocks
  5. Charge pressure
  6. Clickers and spring preload
  7. Cold weather
  8. Service and replacement
  9. Signs a shock needs attention
  10. Common myths
  11. Makers and OEM examples
  12. Safety

Nearly all modern snowmobile shocks damp with hydraulic oil, including the ones called gas shocks. The real difference is how the nitrogen is kept with the oil. Nitrogen keeps the oil from foaming, so the shock’s damping stays steady when it heats up. Understanding that one point clears up most of the confusion about oil and gas shocks.

Why shocks have nitrogen

Nitrogen pressurizes the oil. Without that pressure, oil can foam or cavitate under fast, repeated compression, and the damping becomes uneven. With nitrogen, the damping stays consistent when hot. Shops use nitrogen rather than air because it is dry and inert, so it does not add moisture or react with the oil.

Emulsion and IFP shocks

Shock designs differ in how they keep the nitrogen apart from the oil:

  • Emulsion shocks mix the nitrogen and oil with no separator. They are usually cheaper, but they can fade sooner.
  • IFP shocks use an internal floating piston to keep the nitrogen and the oil apart.

Remote reservoirs

Some shocks have a remote or piggyback reservoir. The reservoir adds oil volume and helps the shock shed heat. Remote reservoirs often carry the compression adjusters.

Air shocks

Air shocks, such as the FOX FLOAT, use air as the spring. They are still oil-damped, so the damping works the same way as in other shocks.

Charge pressure

Nitrogen charge is commonly around 100 to 250 psi, depending on the model. Use the figure in your service manual. Do not recharge a shock with shop air, because compressed air is not the same as dry nitrogen.

Clickers and spring preload

Clickers adjust damping, which controls how quickly the shock moves. Spring preload is a separate adjustment that sets ride height and sag. Changing one does not change the other. For preload and sag, see how to set rear suspension sag on a snowmobile.

Cold weather

Cold oil is thicker, so shocks feel stiffer until they warm up. Give the sled a short warm-up before you judge how it rides.

Service and replacement

Rebuildable shocks are often serviced once a year, or every 1,000 to 2,000 miles, depending on the maker. Non-rebuildable OEM gas shocks are replaced when they wear out. Check your maker’s interval rather than guessing.

Signs a shock needs attention

  • Oil leaking from the shaft or body
  • Bouncing after a bump
  • Slow or no rebound
  • A pitted shaft

Common myths

  • “Gas shocks have no oil.” They do.
  • “The gas charge is the main spring.” It adds only a small extending force. The spring does most of the work.
  • “You can recharge a shock with shop air.” Do not.
  • “More compression damping always cures bottoming.” It is not always the fix.

Makers and OEM examples

Common shock makers include FOX, KYB, and Walker Evans. OEM examples include Ski-Doo’s HPG/KYB Pro and the FOX QS3, which has three-position compression adjustment. These are examples, not recommendations.

Safety

Release the nitrogen pressure before you take a shock apart, following the maker’s procedure. Never heat or puncture a pressurized shock or reservoir.

For where the shocks sit in the rear suspension, read what is a skid on a snowmobile?. For the wider picture, see snowmobile tracks and rear suspension explained.

The complete guide to tracks and suspension

Snowmobile Tracks and Rear Suspension Explained
Read the guide

Keep exploring

Guides from other topics

All topics →