Tracks and Suspension

How to Remove a Snowmobile Skid and Track

How to remove a snowmobile skid and track: tools, support, skid bolts, driveshaft and track removal, parts to inspect, reassembly, and safety.

On this page
  1. How hard is it to change the track on a snowmobile?
  2. Tools and setup
  3. Step 1: Slacken the track and support the skid
  4. Step 2: Remove the skid bolts
  5. How do you remove the rear shock?
  6. Step 3: Pull the skid out of the track loop
  7. Step 4: Remove the driveshaft and the track
  8. Inspect while it is apart
  9. Reassembly notes
  10. Common myths
  11. Safety

Removing a snowmobile track is a bigger job than adjusting its tension. The track is a closed loop, so you have to take the skid out of the track loop, then remove the driveshaft to free the track. This guide covers the tools, the order of steps, and what to check while everything is apart. Your model’s service manual overrides any general guide, because the order and parts vary by model.

How hard is it to change the track on a snowmobile?

It is a practical job for a home mechanic with the right tools, a service manual, and a safe way to support the sled. It is more involved than a tension adjustment, because the skid and the driveshaft both come out. Plan for a longer job, and do not rush the support steps.

Tools and setup

You will need:

  • A socket set and breaker bar
  • A torque wrench
  • A rear stand or hoist, and a floor jack
  • Threadlocker, for any bolt where the manual calls for it
  • The service manual for your model

Support the rear on a stand or hoist. Do not tip the sled on its side, which can cause fluid leaks and scuff the plastics. Never rely on a jack alone to hold the sled up.

Step 1: Slacken the track and support the skid

Back the track adjusters off fully so the track has slack. Place a floor jack under the skid. As the skid bolts come out, the shocks and springs extend, so the jack has to take that load.

Step 2: Remove the skid bolts

Remove the main skid bolts through the tunnel. There are usually four, with a front and a rear arm bolt on each side, though the number and order vary by model. Some models need an extra part disconnected first, such as a shock mount. Check the manual for your model before you remove anything.

How do you remove the rear shock?

Rear shock removal depends on the model, so the steps are model-specific. In general, the shock is held at its mounts on the skid, and some models need brackets or fasteners removed first. Shocks and springs store energy, so control them as you disconnect them and keep your hands clear. Follow the service manual for your sled rather than a general guide. If you plan to take the shock apart for service, see snowmobile shock absorbers: oil vs gas explained.

Step 3: Pull the skid out of the track loop

Once the bolts are out, lower the skid and pull it out of the track loop. The rail and clip edges are sharp, so wear gloves and keep your fingers clear of pinch points.

Step 4: Remove the driveshaft and the track

The track cannot come off until the driveshaft is removed. The exact steps vary by model, but in general:

  • On models with a chaincase, drain the oil, remove the cover, then remove the tensioner, the chain, and the lower sprocket.
  • Remove the bearing housing on the opposite side of the driveshaft, along with any brake parts mounted on the driveshaft.
  • Slide the driveshaft out of the sled, then lift the track out.

Check the manual before you drain any oil, and have a container ready.

Inspect while it is apart

With the track and skid off, check the parts you rarely see:

  • Drive sprockets and drivers, which can wear and damage a new track
  • Driveshaft bearings and the bearing housings
  • Hyfax on the slide rails (see snowmobile hyfax: when and how to replace slide rails)
  • Idler wheels and their bearings
  • The chain and tensioner, if your model has them

Replace worn parts now, while the sled is apart.

Reassembly notes

Reassembly reverses these steps. Replace self-locking nuts where the manual specifies them. Torque bolts to spec, and use threadlocker where the manual calls for it. Do not reuse old skid bolts without checking them against the manual.

For the track installation steps, see how to install a snowmobile track, step by step. Once everything is back together, set tension and alignment before you ride. See how to adjust snowmobile track tension.

Common myths

  • “The track comes off without pulling the driveshaft.” It does not, because the track is a closed loop.
  • “One removal order fits every model.” The order varies, so check your manual.
  • “You must always unload the torsion springs to drop the skid.” Whether you need to depends on the model, so check the manual rather than assuming either way.
  • “Old bolts can always go back in dry.” Use threadlocker where the manual calls for it.

Safety

Never work under a sled held only by a jack. Springs and shocks store energy, so keep your hands clear as the skid extends. Wear gloves, because the rail and clip edges are sharp. Support the sled on a stand or hoist for the whole job.

If the parts are unfamiliar, start with what is a skid on a snowmobile?. For the wider picture, see snowmobile tracks and rear suspension explained.

The complete guide to tracks and suspension

Snowmobile Tracks and Rear Suspension Explained
Read the guide

Keep exploring

Guides from other topics

All topics →