Gear and Trips

Heated Grips and Gloves for Snowmobiling

Heated grips and gloves for snowmobiling: how factory and aftermarket grips work, battery vs sled-powered gloves, run times, and keeping hands warm.

On this page
  1. How heated grips work
  2. Check your sled’s power before you add heat
  3. Hand guards and wind blocking
  4. Heated gloves: battery or sled power
  5. Mitts or gloves
  6. Liners, layers and chemical warmers
  7. Keeping gloves dry
  8. Heat settings and comfort
  9. Battery safety
  10. Numb hands are a control problem

Heated grips warm your palms, and heated gloves cover your fingers and the backs of your hands. Grips don’t replace warm gloves. Many riders use both when the temperature drops, and the right mix depends on your sled and how you ride.

How heated grips work

Most new sleds come with heated grips and a heated thumb warmer from the factory. They usually have several heat levels, and you adjust them from a switch on the handlebar or from the gauge display. The number of settings depends on the model.

Aftermarket heated grip kits are also available. They wire into the sled’s 12-volt electrical system and come with their own controller. Installation is a wiring job, so follow the kit’s instructions closely, and consider having a dealer or an experienced installer do it if you’re not comfortable with wiring.

Check your sled’s power before you add heat

Heated accessories draw power from the sled’s electrical system. Check your sled’s stator output and the wattage limit in the owner’s manual before you add several electric accessories, such as heated grips, lights and a heated shield. A low-output system can struggle if it’s asked to run too much at once.

Check first, then add. If the manual doesn’t list a limit, ask a dealer before you wire anything in.

Hand guards and wind blocking

Hand guards, or wind deflectors, block the airflow that chills your hands. They can make a large difference to how warm your grips feel, and they work with heated grips rather than against them. Mountain riders often choose stiffer guards. Our accessories article covers hand guards and other sled options in more detail.

Heated gloves: battery or sled power

Heated gloves usually run on rechargeable lithium-ion battery packs. These packs are commonly rated at 7.4 volts. Run time depends on the heat setting and the brand, and it often falls somewhere between about two and eight hours. Treat published run times as a range, not a promise.

Some heated gloves can be wired to the sled’s 12-volt power instead of batteries. That removes the need to recharge, but it adds wiring and puts more load on the sled. Check the sled’s output first.

Battery ratings are often measured on the lowest setting. If you run the gloves on high, expect the battery to last less time than the rating suggests.

Mitts or gloves

Mitts are warmer than gloves because your fingers share one space. Gloves give better control of the levers and throttle, which matters for braking and steering.

Trail riders often choose gauntlet-style gloves that cover the jacket cuff. Mountain riders often use thinner gloves with more layers underneath. Choose based on how much dexterity you need and how cold you expect it to get.

Liners, layers and chemical warmers

Glove liners add warmth and let you take off the outer glove for small tasks, like tying a strap or adjusting a bag, without exposing your bare hands for long.

Chemical hand warmers can add warmth for several hours. They need oxygen to work, so they perform less well in tight gloves. Leave room for them.

Keeping gloves dry

Gloves soak through from sweat and snow, and wet gloves lose their insulation. Carry a spare pair on every ride. At the end of the day, dry gloves on a boot or glove dryer, or in a warm, ventilated spot away from direct heat. High direct heat can damage the materials and the heating elements.

Heat settings and comfort

Running heat at the maximum setting all day isn’t always better. It can make you sweat, and then your hands can get cold and wet. Use the lowest setting that keeps your hands comfortable, and adjust as you warm up or cool down.

Tight gloves aren’t warmer. Gloves that are too tight restrict blood flow, so your hands get colder. Choose a size that fits with your liner on.

Battery safety

Don’t charge or store a damaged or wet lithium battery. Follow the maker’s charging and storage instructions, and keep batteries out of extreme cold when you’re not using them. If a battery looks swollen, is damaged or has been wet, stop using it and follow the manufacturer’s guidance on disposal.

Numb hands are a control problem

Numb fingers reduce your control of the throttle and brakes. If your hands go numb, stop and warm up before you keep riding. Don’t keep going and hope they warm up on their own. Our guide to what is too cold for snowmobiling covers wind chill and frostbite risk.

For more on the layers and gear that go with heated hand gear, see our snowmobile gear guide. The trip packing list covers spare gloves and the rest of what to carry on longer rides.

The complete guide to gear and trips

Snowmobile Gear Guide: What to Wear for Warmth and Safety
Read the guide

Keep exploring

Guides from other topics

All topics →